September 21, 2021 - The mass simulator for the Rubin Observatory LSST Camera was shipped from SLAC National Accelerator Laboratory on September 3rd, 2021, and arrived successfully on the summit of Cerro Pachón, in Chile, on September 13th. This shipment was an important test run for the valuable and delicate LSST Camera, which is scheduled to ship to Chile from SLAC next year. The entire shipment process was carefully monitored and tested to record any events that might indicate the possibility of damage to the LSST Camera, and we're happy to report that not a single one occurred!
The mass simulator, built by the company Moog, is a steel structure that provides the mass, center of gravity, general shape, and physical interfaces of the LSST Camera. Its purpose is to stand in for the real camera in a variety of tests performed before the camera is finished, and to test systems beforehand to make sure that the LSST Camera won't be inadvertently damaged. The mass simulator was used at SLAC to verify the LSST Camera rotator on the camera integration stand. With this test shipment, the mass simulator has made an even more significant contribution, helping the Camera team collect extensive data and thereby anticipate the conditions that the LSST Camera will encounter on its journey next year.
Many of the more durable Rubin components were sent to Chile by ship, but with dozens of stops on a shipping route, cargo containers can be exposed to weeks of weather, jostling, and sometimes even changing vessels along the way. To minimize the risk of damage during shipping, the shipping plan for the LSST Camera specifies air travel instead, so that's how the mass simulator went too. The container holding the mass simulator left SLAC on a transport vehicle on September 3rd, heading to Florida, where it waited a couple of days until its scheduled flight on September 10th. Although the Camera team had requested a direct flight from Miami to Santiago, the plane ended up going to Brazil first—extra stops are common for cargo flights. This didn't affect the shipment, but because extra time in transit increases the chance of unexpected events, the LSST Camera will travel on a specially chartered flight, departing from California.
During the trip, a variety of instruments measured the conditions affecting both the shipping container and the camera mass simulator, which was packed carefully in the container, on a vibration isolation system. Accelerometers that measured vibrations recorded no large impacts on the shipping container, and no notable transmissions of vibrations onto the mass simulator. GPS trackers were installed on the container, broadcasting its location every 30 minutes, along with temperature information and light levels (in case the container was opened). Data loggers were also set up to record temperature and humidity inside the container, which was insulated to minimize temperature extremes. The LSST Camera, when it ships, will be bagged with desiccant to ensure it stays clean and dry; preliminary temperature and humidity data from the mass simulator shipment support that these preparations will be sufficient to protect the LSST Camera.
Further analysis of the data will determine whether any design changes are necessary, but so far it looks like improvements will mainly focus on the shipping procedure. For example, there was some unanticipated road work going on while the shipping container was being transported up the mountain, and with some additional coordination and planning that could be prevented when the LSST Camera arrives.
The mass simulator is now stored on the 3rd level of the Rubin summit facility building, and will be used as necessary for Commissioning activities before the LSST Camera arrives. Congratulations to the Camera team for completing this shipment successfully after many months of preparation and planning.
Financial support for Rubin Observatory comes from the National Science Foundation (NSF) through Cooperative Agreement No. 1258333, the Department of Energy (DOE) Office of Science under Contract No. DE-AC02-76SF00515, and private funding raised by the LSST Corporation. The NSF-funded Rubin Observatory Project Office for construction was established as an operating center under management of the Association of Universities for Research in Astronomy (AURA). The DOE-funded effort to build the the Rubin Observatory LSST Camera (LSSTCam) is managed by the SLAC National Accelerator Laboratory (SLAC).
The National Science Foundation (NSF) is an independent federal agency created by Congress in 1950 to promote the progress of science. NSF supports basic research and people to create knowledge that transforms the future.
NSF and DOE will continue to support Rubin Observatory in its Operations phase. They will also provide support for scientific research with LSST data.
Contact | Employment | LSST Corporation